264 VALVE HARDWARE Z-Bore Valve System There are three spud types available: the standard clamp-in spud, a screw-in spud and an angle screw-in spud. There is no temporary outside-in clamp-in spud for Z-Bore. The Z-Bore Valve System is very similar to the Super Large Bore System. By using an O-Ring to seal the clamp-in spud to the rim, a greater flow diameter is created without sacrificing strength or performance. Flows 370 CFM compared to 240 CFM on the Z-Bore Valve System. Z-1 SCREW-IN SPUD • The screw-in spud is used to attach any Z-Bore valves to the rim • Designed to screw into a 1/2" NPT-tapped rim hole • Can be changed without demounting the tire ASCOT NO. MFG. NO. DESCRIPTION 466-70001 Z-1 466-70001 Screw-In Spud Z-13 SCREW-IN SPUD • The Z-13 screw-In spud screws into the 3/4" NPT-tapped rim hole and converts Mega Bore to Z-Bore ASCOT NO. MFG. NO. 466-70013 Z-13 DESCRIPTION Screw-In Spud 466-70013 ANGLE CONNECTOR • Connectors of various angles and lengths are available • The connector accommodates a flexible extension which attaches to the Z-10 core housing ASCOT NO. MFG. NO. DESCRIPTION 469-70360 466-70375 466-70380 466-70390 Z3-60 Z3-75 Z3-80 Z3-90 60° Angle 75˚ Angle 80˚ Angle 90˚ Angle 466-70390 Z-BORE FLEXIBLE EXTENSIONS • Made up in any length to allow extension to fit the wheel configuration • Specially designed fittings and thermoplastic hose will not fatigue or crush during service • Corrosion problems are eliminated • Able to customize extension in the field • ZFAK field assembly kit available to assemble your own ASCOT NO. MFG. NO. 466-70700 ZBFELength 466-70701 ZFAK DESCRIPTION Flexible Extension Assembly Kit For Z-Bore Valves. INCLUDES: Contains Z-8 Swivel Connector, Z-7 Straight Tubing Connector, 2x Z2-2 Nuts, 2x Z-9 Tubing Connector Sleeves, Z-10 Core Housing. Z-100 Tubing Is Ordered Separately Z-10 CORE HOUSING • Complete with core and cap • Integral part of the system as the Z-10 is removed from the valve assembly with the Haltec Z-12B inflator to utilize the larger opening and the fullest flow ASCOT NO. MFG. NO. DESCRIPTION 466-70010 Z-10 Z-12L INFLATOR • To maximize air flow, a Z-12B inflator is used to remove core housing during inflation and deflation • Operates like the IN-100A Super Large Bore inflator Core Housing w/Core & Cap 466-70010 ASCOT NO. MFG. NO. 466-70012 Z-12L DESCRIPTION Inflator 466-70012 Z-4 ANGLE SCREW-IN SPUD • Fits 1/2" NPT-tapped rim hole • 85˚ bend angle ASCOT NO. MFG. NO. DESCRIPTION 466-70004 Z-4 Z-2 CLAMP-IN SPUD • Can attach any Z-Bore valve to the rim through a standard valve hole (13/16") • Fits a 13/16" diameter valve hole • Tire must be dismounted to change spud ASCOT NO. MFG. NO. 466-70002 Z-2 DESCRIPTION Clamp-In Spud 466-70002 Angle Screw-In Spud 466-70004 BUYER'S GUIDE ASCOT SUPPLY CORPORATION WARNING: For more information go to www.P65Warnings.ca.gov. SUPPLY CORPORATION VALVE HARDWARE
49 Publizr Home